{"id":1670,"date":"2026-09-10T07:04:20","date_gmt":"2026-09-10T07:04:20","guid":{"rendered":"https:\/\/plasticcastors.com\/product\/150mm-6-inch-nylon-wheel\/"},"modified":"2026-09-11T03:04:35","modified_gmt":"2026-09-11T03:04:35","slug":"150mm-6-inch-nylon-wheel","status":"publish","type":"product","link":"https:\/\/plasticcastors.com\/vi\/san-pham\/150mm-6-inch-nylon-wheel\/","title":{"rendered":"150 mm \/ 6 Inch Nylon Wheel"},"content":{"rendered":"
\n
\n
\n
\n

Where 150 mm \/ 6 Inch Nylon Wheel fits in a selection<\/h2>\n

For an industrial buyer, 150 mm \/ 6 Inch Nylon Wheel is not a label to choose in isolation. The useful question is how it behaves inside the complete wheel, mounting and duty-cycle decision.<\/p>\n

For industrial trolleys, equipment bases and replacement-wheel enquiries where the shaft\/bore interface is confirmed, begin by confirming the actual carried load, wheel\/ground contact and attachment geometry. This is usually more useful than comparing nominal product names because two visually similar wheels can behave differently once mounting, floor condition and real load distribution are considered.<\/p>\n

This also prevents a frequent sourcing error: choosing from appearance alone. A wheel can fit visually and still fail to match the axle, bracket, stowed envelope or duty cycle. Record total equipment weight, supporting points, floor condition, axle or bracket measurements, expected manoeuvring and quantity in the enquiry so the commercial discussion starts from a technically meaningful baseline. For 150 mm \/ 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.<\/p>\n<\/div>\n

\n
\"150<\/figure>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
\n
\n

Known configuration details for 150 mm \/ 6 Inch Nylon Wheel<\/h2>\n

150 mm \/ 6 Inch Nylon Wheel is presented as a procurement-ready configuration rather than a one-number commodity. Verified details for this item include wheel diameter: 150 mm (6 in nominal), wheel width: 50 mm, material: Nylon. Any interface or performance value that is not listed should be confirmed against the equipment before quotation.<\/p>\n

For replacement work, photograph the existing assembly from the side and mounting face, then record wheel diameter, wheel width, hub or axle dimensions, overall installed height and nearby clearance. For a new design, include the drawing or mounting envelope. For 150 mm \/ 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.<\/p>\n<\/div>\n

\n
\"B\u1ea3ng<\/figure>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
\n

Verified specification data for 150 mm \/ 6 Inch Nylon Wheel<\/h2>\n

B\u1ea3ng n\u00e0y ph\u00e2n t\u00e1ch c\u00e1c th\u00f4ng tin c\u1ea5u h\u00ecnh hi\u1ec7n t\u1ea1i kh\u1ecfi c\u00e1c m\u1ee5c c\u1ea7n x\u00e1c nh\u1eadn d\u1ef1 \u00e1n. M\u1ed9t con s\u1ed1 kh\u00f4ng \u0111\u01b0\u1ee3c li\u1ec7t k\u00ea s\u1ebd t\u1ea1o ra nhi\u1ec1u r\u1ee7i ro h\u01a1n so v\u1edbi m\u1ed9t \u0111i\u1ec3m x\u00e1c nh\u1eadn \u0111\u01b0\u1ee3c \u0111\u00e1nh d\u1ea5u r\u00f5 r\u00e0ng.<\/p>\n

\n\n\n\n\n\n\n\n\n\n
Tham s\u1ed1<\/th>\nC\u1ea5u h\u00ecnh hi\u1ec7n t\u1ea1i<\/th>\n<\/tr>\n<\/thead>\n
\u0110\u01b0\u1eddng k\u00ednh b\u00e1nh xe<\/td>\n150 mm (6 inch)<\/td>\n<\/tr>\n
Chi\u1ec1u r\u1ed9ng b\u00e1nh xe<\/td>\n50 mm<\/td>\n<\/tr>\n
V\u1eadt li\u1ec7u<\/td>\nNylon<\/td>\n<\/tr>\n
C\u1ea5u h\u00ecnh<\/td>\nCh\u1ec9 c\u00f3 b\u00e1nh xe<\/td>\n<\/tr>\n
Giao di\u1ec7n l\u1eafp \u0111\u1eb7t<\/td>\nX\u00e1c nh\u1eadn y\u00eau c\u1ea7u v\u1ec1 tr\u1ee5c\/\u0111\u01b0\u1eddng k\u00ednh l\u1ed7 trong y\u00eau c\u1ea7u b\u00e1o gi\u00e1.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
\n
\n

Duty conditions to review for 150 mm \/ 6 Inch Nylon Wheel<\/h2>\n

Industrial trolleys, equipment bases and replacement-wheel enquiries where the shaft\/bore interface is confirmed. Selection should still account for floor joints, ramps, side loads, impacts and periods of stationary load. Where the wheel is part of a trailer support assembly, separate the vertical support task from manoeuvring effort and check that the jack can retract or fold without striking the drawbar, coupling or ground.<\/p>\n

For equipment carts, usable load per wheel may not equal total load divided by wheel count if the floor is uneven or the frame is not perfectly rigid. For 150 mm \/ 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.<\/p>\n<\/div>\n

\n
\"150<\/figure>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
\n
\n

Load and movement checks for this industrial wheel \u2014 150 mm \/ 6 Inch Nylon Wheel<\/h2>\n

Start with equipment dead weight, maximum payload and the number of wheels that reliably support the frame. Add an application-appropriate allowance for uneven load sharing, floor transitions and impact. For trailer jacks, distinguish the static nose or drawbar load from the effort required to manoeuvre the trailer. For 150 mm \/ 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.<\/p>\n

Wheel diameter influences obstacle crossing and clearance, while material and bearing choice influence rolling behaviour. None of those variables substitutes for the actual rating of the selected assembly. For 150 mm \/ 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.<\/p>\n<\/div>\n

\n
\"T\u00ednh<\/figure>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
\n
\n

Installation interface checks for 150 mm \/ 6 Inch Nylon Wheel<\/h2>\n

Before release, compare the mounting interface against the equipment. For a loose wheel this means bore or bearing type, axle diameter, hub length, spacers and side clearance. For a jockey or guide-wheel assembly it also includes tube diameter, clamp or plate geometry, fastener access, crank clearance, retracted height and the path used when the assembly swivels or folds. For 150 mm \/ 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.<\/p>\n

Kh\u00f4ng n\u00ean c\u1ed1 g\u1eafng gh\u00e9p kh\u00edt b\u1eb1ng c\u00e1c mi\u1ebfng \u0111\u1ec7m t\u1ef1 ch\u1ebf tr\u1eeb khi kh\u1edbp n\u1ed1i \u0111\u00e3 \u0111\u01b0\u1ee3c thi\u1ebft k\u1ebf cho m\u1ee5c \u0111\u00edch \u0111\u00f3. S\u1ef1 l\u1ec7ch tr\u1ee5c c\u00f3 th\u1ec3 t\u1ea1o ra t\u1ea3i tr\u1ecdng ngang l\u00ean \u1ed5 tr\u1ee5c, g\u00e2y ma s\u00e1t v\u00e0 m\u00e0i m\u00f2n s\u1edbm.<\/p>\n<\/div>\n

\n
\"Giao<\/figure>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
\n
\n

Material and surface conditions for this industrial wheel \u2014 150 mm \/ 6 Inch Nylon Wheel<\/h2>\n

Polymer wheel material should be considered together with floor, contamination, cleaning chemicals, noise expectations and temperature. Nylon and polypropylene are hard thermoplastic families, but exact grade and operating environment still matter. Where the listed configuration specifies a galvanized bracket or tube, that finish applies to the stated configuration only. For 150 mm \/ 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.<\/p>\n

N\u1ebfu c\u00e1c y\u1ebfu t\u1ed1 nh\u01b0 v\u1ea1ch k\u1ebb s\u00e0n, h\u00f3a ch\u1ea5t t\u1ea9y r\u1eeda, \u0111\u1eb7c t\u00ednh \u0111i\u1ec7n ho\u1eb7c nhi\u1ec7t \u0111\u1ed9 b\u1ea5t th\u01b0\u1eddng l\u00e0 quan tr\u1ecdng, h\u00e3y n\u00eau r\u00f5 ch\u00fang. Kh\u00f4ng n\u00ean suy lu\u1eadn c\u00e1c y\u00eau c\u1ea7u \u0111\u00f3 t\u1eeb m\u00e0u s\u1eafc c\u1ee7a b\u00e1nh xe.<\/p>\n<\/div>\n

\n
\"C\u00e1c<\/figure>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
\n
\n

Incoming and installation checks for 150 mm \/ 6 Inch Nylon Wheel<\/h2>\n

On receipt, compare the product against approved dimensions and configuration. Check that the wheel rotates without binding, the bore or bearing seats correctly, fasteners are present where specified and the fork or bracket is free from visible deformation. For a jack assembly, operate the crank through usable travel without load first and confirm folding or swivel movement clears the equipment. For 150 mm \/ 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.<\/p>\n

During commissioning, observe the assembly on the real floor at low speed. Look for rubbing, unusual side movement, loose hardware, wheel wobble and interference with guards or frames. For 150 mm \/ 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.<\/p>\n<\/div>\n

\n
\"Minh<\/figure>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n
\n

Information to include when quoting 150 mm \/ 6 Inch Nylon Wheel<\/h2>\n