산업용 바퀴 및 지지대 조립

150 mm / 6 Inch Nylon Wheel

Name: 150 mm / 6 Inch Nylon Wheel | PlasticCastors.com
SKU: PC-NW-150

150 mm / 6 Inch Nylon Wheel for B2B equipment or trailer support projects. Specify the fit-controlling interface, duty and quantity for quotation.

휠 직경
150mm (공칭 6인치)

휠 폭
50mm

재료
나일론

구성
휠만

이 구성을 요청하세요

Where 150 mm / 6 Inch Nylon Wheel fits in a selection

For an industrial buyer, 150 mm / 6 Inch Nylon Wheel is not a label to choose in isolation. The useful question is how it behaves inside the complete wheel, mounting and duty-cycle decision.

For industrial trolleys, equipment bases and replacement-wheel enquiries where the shaft/bore interface is confirmed, begin by confirming the actual carried load, wheel/ground contact and attachment geometry. This is usually more useful than comparing nominal product names because two visually similar wheels can behave differently once mounting, floor condition and real load distribution are considered.

This also prevents a frequent sourcing error: choosing from appearance alone. A wheel can fit visually and still fail to match the axle, bracket, stowed envelope or duty cycle. Record total equipment weight, supporting points, floor condition, axle or bracket measurements, expected manoeuvring and quantity in the enquiry so the commercial discussion starts from a technically meaningful baseline. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

150 mm / 6 Inch Nylon Wheel product family context

Known configuration details for 150 mm / 6 Inch Nylon Wheel

150 mm / 6 Inch Nylon Wheel is presented as a procurement-ready configuration rather than a one-number commodity. Verified details for this item include wheel diameter: 150 mm (6 in nominal), wheel width: 50 mm, material: Nylon. Any interface or performance value that is not listed should be confirmed against the equipment before quotation.

For replacement work, photograph the existing assembly from the side and mounting face, then record wheel diameter, wheel width, hub or axle dimensions, overall installed height and nearby clearance. For a new design, include the drawing or mounting envelope. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

Verified specification data for 150 mm / 6 Inch Nylon Wheel

이 표는 현재 구성 정보와 프로젝트 확인이 필요한 항목을 구분합니다. 표에 표시되지 않은 항목은 명확하게 표시된 확인 지점보다 더 큰 위험을 초래합니다.

매개변수	현재 구성
휠 직경	150mm (공칭 6인치)
휠 폭	50mm
재료	나일론
구성	휠만
장착 인터페이스	견적 요청서에서 차축/보어 요구 사항을 확인하십시오.

Duty conditions to review for 150 mm / 6 Inch Nylon Wheel

Industrial trolleys, equipment bases and replacement-wheel enquiries where the shaft/bore interface is confirmed. Selection should still account for floor joints, ramps, side loads, impacts and periods of stationary load. Where the wheel is part of a trailer support assembly, separate the vertical support task from manoeuvring effort and check that the jack can retract or fold without striking the drawbar, coupling or ground.

For equipment carts, usable load per wheel may not equal total load divided by wheel count if the floor is uneven or the frame is not perfectly rigid. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

150 mm / 6 Inch Nylon Wheel application context

Load and movement checks for this industrial wheel — 150 mm / 6 Inch Nylon Wheel

Start with equipment dead weight, maximum payload and the number of wheels that reliably support the frame. Add an application-appropriate allowance for uneven load sharing, floor transitions and impact. For trailer jacks, distinguish the static nose or drawbar load from the effort required to manoeuvre the trailer. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

Wheel diameter influences obstacle crossing and clearance, while material and bearing choice influence rolling behaviour. None of those variables substitutes for the actual rating of the selected assembly. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

Installation interface checks for 150 mm / 6 Inch Nylon Wheel

Before release, compare the mounting interface against the equipment. For a loose wheel this means bore or bearing type, axle diameter, hub length, spacers and side clearance. For a jockey or guide-wheel assembly it also includes tube diameter, clamp or plate geometry, fastener access, crank clearance, retracted height and the path used when the assembly swivels or folds. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

설계 당시 고려되지 않은 연결 부위라면, 임시방편으로 만든 스페이서를 사용하여 억지로 끼워 맞추지 마십시오. 정렬 불량은 베어링에 측면 하중을 발생시켜 마찰과 조기 마모를 초래할 수 있습니다.

Material and surface conditions for this industrial wheel — 150 mm / 6 Inch Nylon Wheel

Polymer wheel material should be considered together with floor, contamination, cleaning chemicals, noise expectations and temperature. Nylon and polypropylene are hard thermoplastic families, but exact grade and operating environment still matter. Where the listed configuration specifies a galvanized bracket or tube, that finish applies to the stated configuration only. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

바닥 표시, 세척제 화학 물질, 전기적 특성 또는 특수한 온도 조건이 중요한 경우, 해당 사항을 명확하게 명시하십시오. 이러한 요구 사항은 휠 색상에서 추론해서는 안 됩니다.

Incoming and installation checks for 150 mm / 6 Inch Nylon Wheel

On receipt, compare the product against approved dimensions and configuration. Check that the wheel rotates without binding, the bore or bearing seats correctly, fasteners are present where specified and the fork or bracket is free from visible deformation. For a jack assembly, operate the crank through usable travel without load first and confirm folding or swivel movement clears the equipment. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

During commissioning, observe the assembly on the real floor at low speed. Look for rubbing, unusual side movement, loose hardware, wheel wobble and interference with guards or frames. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

Information to include when quoting 150 mm / 6 Inch Nylon Wheel

제품명 또는 기존 모델 참조 번호(가능한 경우)
분리형 휠의 경우 휠 직경, 너비, 내경/베어링 및 허브 길이
완전 조립품에 필요한 튜브, 클램프, 플레이트, 볼트 구멍 또는 차축 치수
최대 장비 중량, 적재 용량 및 지지 바퀴 수
바닥 또는 지면, 장애물, 화학 물질 및 브레이크 요구 사항
필요한 수량, 목적지 및 도면이나 사진

보다 폭넓은 선택 지침을 보려면 다음을 참조하십시오. 캐스터 및 휠 선택 가이드, 그 측정 가이드 그리고 관련 제품군.

엔지니어링 검토

Engineering fit review for 150 mm / 6 Inch Nylon Wheel

제시된 사양을 출발점으로 삼고, 제품명만으로는 답할 수 없는 적합성 및 작동 관련 질문들을 해결해 나가십시오.

Confirm the fit-controlling interface for 150 mm / 6 Inch Nylon Wheel

150 mm / 6 Inch Nylon Wheel is a wheel-only configuration, so the axle interface deserves the same attention as the outside dimensions. The represented item currently identifies diameter 150 mm (6 in nominal), width 50 mm, material Nylon, configuration Wheel only. Confirm bore or bearing type, axle diameter, hub length, spacer arrangement and side clearance before quotation.

A wheel can match outside diameter and still be unsuitable if the hub geometry changes the installed position or allows the wheel to bind. For replacement work, photograph both sides of the old wheel before removal and record the order of washers, sleeves, spacers and retainers. If the existing part is heavily worn, use stable hub or axle datums rather than copying damage into the target dimensions. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

150 mm / 6 Inch Nylon Wheel fit and measurement review

Match 150 mm / 6 Inch Nylon Wheel to the real operating condition

명시된 재질명(나일론)은 실제 바닥 상태, 오염 정도, 온도 및 이동 패턴과 함께 검토해야 합니다. 경질 열가소성 바퀴는 매끄러운 콘크리트, 바닥 이음매, 경사로 및 이물질이 있는 곳에서 다르게 작동할 수 있습니다. 바닥 보호, 소음 수준 또는 화학적 호환성에 대한 요구 사항이 명시되지 않은 경우, 색상이나 외관만으로 이를 추론해서는 안 됩니다.

For mobile equipment, start with the full equipment mass and payload, then identify how many wheels reliably share the load. Uneven floors and frame flexibility can prevent equal load sharing. Wheel diameter affects obstacle-crossing geometry and installed clearance, while width changes contact area; neither value by itself confirms suitability for the duty. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

150 mm / 6 Inch Nylon Wheel operating context

Check the first installation of 150 mm / 6 Inch Nylon Wheel

Before installation, rotate the wheel on the intended axle or bearing arrangement and check free movement, side clearance and retention. Confirm that the wheel does not contact guards, brackets or adjacent components through the usable range of motion. Fasteners and axle hardware should seat on the intended surfaces rather than being used to force a misaligned hub into position. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

During first use, move the equipment at low speed over the normal route and observe rubbing, wobble, unusual side movement, fastener movement and any change in operator effort. If the route includes a threshold, dock plate or rough joint, include it in the trial. Where a symptom appears, change one variable at a time so the cause is not hidden by a complete assembly swap. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

150 mm / 6 Inch Nylon Wheel inspection and installation review

Build the 150 mm / 6 Inch Nylon Wheel RFQ around measured data

For quotation, separate the values already identified for 150 mm / 6 Inch Nylon Wheel from the dimensions that belong to the machine. The current configuration records Wheel diameter: 150 mm (6 in nominal); Wheel width: 50 mm; Material: Nylon; Configuration: Wheel only; Mounting interface: Confirm axle/bore requirement in RFQ. Those details establish the represented wheel, but they do not establish the axle, bearing, spacer or load condition unless those values are also listed for the item.

A replacement-wheel enquiry becomes more reliable when the buyer records both sides of the hub, the axle diameter, usable hub length, retention method and side clearance. If a bearing is present, identify the bearing arrangement rather than assuming that the visible bore is the running interface. Also state whether wear may have changed the measured outside diameter or width, because a damaged part is not always a dependable dimensional master. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

For a new equipment design, provide the wheel position in the frame and the expected floor route as well as nominal load. This allows diameter, width and material to be reviewed alongside ground clearance, obstacle crossing and neighbouring components. Where a value remains unknown, mark it for confirmation instead of substituting a number from a visually similar wheel. That produces a cleaner comparison and reduces interface mismatch at installation. For 150 mm / 6 Inch Nylon Wheel, keep Wheel diameter 150 mm (6 in nominal) and Wheel width 50 mm attached to this review so a value from another size or assembly is not substituted during quotation.

150 mm / 6 Inch Nylon Wheel quotation and selection boundary

Questions about 150 mm / 6 Inch Nylon Wheel

사진만 보고 인용할 수 있나요?

사진은 식별에 도움이 되지만, 정확한 견적을 위해서는 일반적으로 적합성을 결정하는 치수와 하중 및 수량이 필요합니다.

휠 재질을 변경할 수 있나요?

일부 제품군은 자재 변경이 가능할 수 있지만, 등급, 하중, 바닥 및 공정 최소 기준을 재검토해야 합니다.

교체 부품이 제대로 맞는지 어떻게 확인해야 할까요?

가능하다면 기존 장치를 제거하기 전에 측정하고, 설치된 높이와 여유 공간, 그리고 휠 크기를 비교하십시오.

제품 선택에 있어 정격 하중 정보 하나만으로 충분할까요?

아니요. 하중은 필수적이지만, 설치 위치, 바닥, 휠 재질, 직경, 베어링 배열 및 작동 주기 또한 중요합니다.

Request a quote for 150 mm / 6 Inch Nylon Wheel

견적을 내기 전에 적합성 관련 세부 사항을 검토할 수 있도록 치수, 용도 및 수량을 보내주십시오.

견적 요청